Using a drill can greatly facilitate the repair work. Building tool stores today offer a really huge range of these products, so it is easy for an inexperienced person to get confused in them. It should be borne in mind that the main function of the drill is to drill holes in a variety of materials — wood, metal, concrete, brick, cement mortar or plaster, and so on. Before you buy this equipment, you should find out by what parameters it should be selected. With this, we, perhaps, will begin the review of the best products.
What criteria influence the choice of a drill?
For homework, you should not purchase a professional tool — its price is an order of magnitude higher than that of household structures, but it is unlikely that you will be able to use all the functions of such a drill at home. It is much better to stop at the average parameters of the device. One of the key points is the power consumption of the equipment — a tool with this parameter from 500 to 900 watts is quite suitable for a home. It should be noted that the power of the equipment directly affects the mass of the device, and therefore, the convenience of its use.
Another important point is the idle speed of the shaft — such information is also given in the product data sheet. The higher this parameter is, the smoother the walls of the drilled hole will be. High torque allows even with a small power of the device to work with fairly hard materials. For grinding, this parameter will be an indispensable assistant. It is desirable that there is still a speed adjustment — in this case, the drill can be used as an ordinary screwdriver.
The diameter of the hole is also important — usually the manufacturer gives these maximum and minimum parameters for all basic materials, the diameter of the drill is also indicated. Be sure to pay attention to the cartridge: it can be either quick-clamping or key. The latter variety needs to use a special key, but it holds much more securely, so all powerful and impact products are equipped with this particular cartridge, although the key can be lost. Keyless chucks do not require the use of additional tools, but they last less than key chucks, and are also prone to breakage.
The largest diameter of the drill also plays a role — it is best to purchase drills with this parameter of 13 or 16 mm. A number of additional functions allow to provide convenience of operation of a product and to increase safety. In particular, many drills are equipped with a soft start mechanism, due to which the speed will be gained gradually, there will be no jerks at startup, which ensures an accurate hit in the hole being drilled.
When developing our review, we took into account not only all these points, but also feedback from users and professional repairers, as well as the value for money of the device. We hope that the information provided by us will be very useful for you and will help you quickly decide on the choice of the most suitable model.
The best classic drills
3. Bosch GBM 13 HRE (ZVP)
This model has excellent performance, besides its price is not too high. This drill is perfect for precision drilling work. The torque is 60 Nm, when working with steel, the maximum hole diameter is 13 mm, with aluminum this parameter increases to 20 mm, in wood you can make a hole up to 20 mm. It is possible to adjust the number of revolutions, so the drill can also be used to tighten screws or self-tapping screws. The body is made of durable rubberized plastic, it is comfortable to hold in your hands: it does not slip. An additional handle is included in the kit, which makes the device even more convenient. Management is quite simple — to start the engine, just press the appropriate button. It also has a lever that is responsible for adjusting the number of revolutions.
Reverse rotation is provided, so if the drill gets stuck, it can be easily removed from any material. The design has milled gears, a durable gearbox housing and needle bearings, which increases the service life of the product. The highest power consumption is 550W with an output power of 285W. At idle, the maximum number of revolutions is 550 per minute, under load it does not exceed 380 revolutions.
Advantages:
- High reliability;
- Excellent build quality;
- Torque is good for home use;
- Acceptable price.
Flaws:
- The power cable is short, you will have to immediately stock up on carrying;
- Impact mode is not provided;
- Unreliable wheel for adjusting the number of revolutions.
Bosch GBM 13 HRE (ZVP)
2. Makita DP4001
It has one of the most reliable gearboxes among all the models presented in our review. It delivers up to 51 Nm of torque, making it easy to handle even the toughest jobs that require serious tightening force. The device has everything you need for long and comfortable use. The design provides for a system for adjusting the number of revolutions, an effective reverse. The drill is equipped with a quick-release chuck with one clutch, so you can change drills and nozzles very quickly.
At idle, the device is capable of delivering up to 900 rpm with a power consumption of 750 watts. The weight of the product is only 2.1 kg, it has an additional handle made of rubberized materials. The largest drill diameter is 13 mm, which is quite enough for household work. In metal, using such a drill, you can make a hole with a diameter of up to 13 mm, in wood — up to 38 mm.
Advantages:
- The presence of a keyless chuck;
- Small design;
- If desired, the cartridge can be easily replaced with a key;
- Additional rubberized handle.
Flaws:
- Brushes after a while begin to spark strongly;
- Also, over time, there is a not very pleasant sound when revving.
Makita DP4001
1. DeWalt DWD522KS
This is one of the most comfortable shockless models in use, during the development of which the mass was perfectly balanced, so even with prolonged use, the hands will not get tired. In addition, this design solution greatly reduces vibration, which is especially important when working with hard materials such as steel or concrete. The power of the product is 550 W — it is quite suitable for home conditions. Thanks to this parameter, a hole with a diameter of up to 10 mm can be drilled in metal. The number of revolutions will please you — 2800 per minute at idle, which greatly increases the performance of this tool.
Users praise this model for a long cord and a powerful keyless chuck, the maximum drill diameter does not exceed 10 mm. Electronic type speed control, so you can find the ideal torque for each material. In addition, such a drill is equipped with a torsion button lock. Users notice that there is no additional handle in the kit, which is why holding it is not very convenient.
Advantages:
- Very convenient and reliable cartridge;
- Convenient adjustment of the number of revolutions.
Flaws:
DeWalt DWD522KS
The best impact drills in the budget segment
3. Bort BSM-650U
Powered by an ordinary electrical network, it copes well with materials such as wood, metal and concrete. The model has a reverse mode and a function for adjusting the number of revolutions, which allows you to use the drill as a screwdriver. For even greater ease of use, the additional handle has a special storage compartment for drills — this allows you to keep them at hand during work. The power of the product is 650 W, under the cartridge there is a bright LED that will illuminate the drilled area.
The weight of the drill is 2 kg, it is equipped with a keyless chuck, where you can install a drill with a diameter of up to 13 mm. With this product, you can drill a hole in metal, the diameter of which will be up to 10 mm, in wood — up to 25 mm. The model is equipped with an additional handle with an insert made of dense rough rubber, which will fit snugly into the hand, and the function of impact drilling is provided. This makes it easier to work with concrete and cement.
Advantages:
- Ideal value for money;
- Good product reliability;
- High power;
- The presence of shock mode;
- Long warranty — 2 years.
Flaws:
- The motor gets very hot when running for a long time.
Bort BSM-650U
2. Zubr DU-810 ERM2
This is a fairly inexpensive model that is ideal for home use. The product is placed in a plastic rubberized case, which not only fits comfortably in the hand, but is also not subject to various kinds of damage. The kit comes with an additional handle that makes it easier to use the drill. All controls are located in close proximity to each other, so all operating modes are switched with just one finger. On the engine start button there is a wheel that regulates the speed, above it there is a lever that responds to the choice of operating mode — normal or reverse. There is a button on the left side of the main handle for continuous operation.
Among inexpensive models, this is one of the most powerful drills — this figure is 810 W, the number of idle revolutions is 2800 per minute. The chuck is set with a key, which is very important to ensure safety with such a torque. The number of strokes per minute reaches 42,000. This feature greatly facilitates the work with the hardest materials. Users also note a fairly long warranty for this device — as much as 5 years.
Advantages:
- Very comfortable design;
- Lightweight and compact, making it suitable for use in hard-to-reach places;
- Good for home use;
- Sufficiently long power cable;
- Excellent value for money.
Flaws:
- Sometimes models come across with a strong backlash of the cartridge, so it should be replaced immediately after this defect is revealed.
Zubr DU-810 ERM2
1. Interskol DU-580ER
This is the best impact drill in a fairly cheap price segment. It is distinguished by excellent workmanship, has advanced functionality, and therefore deservedly enjoys popularity. The power of the product is 580 W, thanks to this indicator, it is possible to drill holes in concrete with a diameter of up to 12 mm. When idling, the device produces up to 2800 rpm, which allows for a high level of performance. The weight of the device is only 1.4 kg — it can be easily held even with one hand.
The handles are ergonomic, do not slip out of the palms. The design is made of high quality materials, due to which, therefore, it is characterized by a long period of operation, and all functions will work in normal mode. Impact drilling facilitates work with hard materials, reverse rotation is provided. The kit comes with an additional handle, the cable is elongated, so you can use it without an extension cord. There is a special limiter to obtain a hole of a given length. The only negative point that users note is that the engine gets very hot during operation.
Advantages:
- High power for home use;
- Good production quality;
- Working power adjustment;
- Acceptable power;
- Extended power cable.
Flaws:
- In addition to a heating motor during long operation, it was not detected.
Interskol DU-580ER
The best impact drills in terms of value for money
3. DeWalt DWD024
This model differs in small overall dimensions that allows to hold it even with one hand. Just in case, the manufacturer supplied this drill with an additional rubberized handle. It is useful if you have to work with materials that require additional effort when drilling. The chuck is key here, as with most impact drills. It allows you to securely clamp the drill or drill, does not allow it to slip, which often happens with keyless chucks. There is a special mechanism that provides precise adjustment of the drilling depth.
For continuous operation, there is a special button that blocks the engine shutdown. The design has a reverse function, so the drill can also be used as a screwdriver. Adjustment of the number of revolutions and speed is smooth, without jerks. It has a power of 650 W with a weight of less than 2 kg. Users note a fairly long power cord — 2.5 meters, thanks to which you can use this device without an extension cord.
Advantages:
- Excellent build quality, no backlash and extraneous squeaks;
- Reliable cartridge;
- Long service life;
- High power.
Flaws:
- Not suitable for mixing mortars.
DeWalt DWD024
2. Makita HP1620
This is a universal drill that can drill not only hard materials, but also softer ones — plastic, drywall, and so on. The rotation speed is regulated quite smoothly, which allows you to choose the required number of revolutions for a particular material. The maximum number at idle is 2800 per minute. If the device is used in shock mode, then there will be up to 44,800 beats per minute. There is a reverse, carbon brushes, due to which the power will be maintained both in the main and in the reverse mode. The body is made of durable plastic that can withstand severe physical exertion — bumps, falls, and so on. The mass of the device is small, so you can easily hold it in your hands for quite a long time.
The power consumption of the drill is 650 W, the output is 380 W. The device operates on the basis of a universal commutator motor, the maximum diameter of the installed drill is 13 mm. The cartridge is key, on the power cable there is a special clip for storing the key. Many users note that the drill can work with a number of materials such as glass, hardened steel, plywood, granite, marble, and so on.
Advantages:
- Ideally works both in shock and in normal mode;
- Small mass;
- Beautiful appearance, body made of impact-resistant plastic.
Flaws:
- No case included.
Makita HP1620
1. Bosch PSB 750 RCE Case (BZP)
This is the best impact drill in terms of value for money and according to user reviews. The device is distinguished by excellent reliability, truly German, although the cost is quite high compared to other models, such a drill is still very popular. This design is equipped with a convenient keyless chuck, which is not quite typical for an impact drill. It is reliable enough, so drills or drills will not slip during operation, besides, it can be used to quickly replace the drill. The power of the product is 750 W — one of the highest among all the models included in our review. The highest torque is 10 Nm, so the device will quickly pass even through fairly hard materials.
The kit comes with a decent-sized case, which will include not only the drill itself, but also various additional nozzles, crowns, drills, and so on. A drilling depth limiter is provided, it is made of a rigid metal rod. It is possible to fix the spindle. The device is able to work for quite a long time without overheating. The brushes here are carbon, resistant to abrasion, do not spark during operation.
Advantages:
- High-quality German assembly;
- All parameters declared by the manufacturer are true.
Flaws:
- During dusty work, the reverse can become clogged, otherwise the device has no negative points.
Bosch PSB 750 RCE Case (BZP)
In conclusion, an interesting video
In conclusion, we want to express the hope that all the information turned out to be quite useful for you. If you have certain considerations regarding a particular model, or if you are going to share your experience with other users, then comments on this article are at your disposal.